Skip to main content
Skip table of contents

Shelly i3 Device Smart Control

Main Controls

The power button is at the bottom of this tab. Tap the power button to turn your device On/Off. Your device is on when there is a blue ring around the power button , and is off when the ring is gray.

Notifications

If you have Shelly Device notifications, they will appear on this tab. View the number of notifications for this Shelly Device. Tap the X button in the top right corner of the notification box if you wish to delete the notification.

Activity log

Observe the recorded history of the Shelly Device events. See the date, time and type of action executed such as the Device being switched On/Off.

Actions

Use events to trigger http endpoints. Add URLs to execute when actions are complete. Tap the edit icon of the action you wish to activate in order to add URLs.

Add URLs to the following actions:

  • Button on

  • Button off

  • Short push

  • Long push

  • Double short push

  • Triple short push

  • Short push + Long push

  • Long push + Short push

Follow these steps to add URLs:

  • Tap the edit pencil icon next to the action to which you wish to add URLs.

  • Tap + Add URL to add up to 5 URLs per action, which will be executed one after the other. Tap the trash icon if you wish to delete a URL.

  • Tap Save once you have added your URLs.

Tap the toggle to enable the action. This function requires a working connection to the Internet. Please note that more than two URLs per action can affect the normal operation of the device depending on the network infrastructure and controlled devices.

Networks

Wi-Fi

Register the Shelly device to connect to up to 2 different Wi-Fi networks. Either input or select the Wi-Fi network. Can select an open network, and also set a static IP address. Enable Wi-Fi 1, or Wi-Fi 2, or both at the same time. If both Wi-Fi 1 and Wi-Fi 2 are enabled, and the Shelly device disconnects from one of the networks, it will connect to the other. Tap Save to save any changes made.

Access Point

Mark the checkbox to enable this function. Enable to configure Shelly Device to create a Wi-Fi Access Point (AP), to which you can connect. Observe the SSID. Set a password to protect your device’s access point to secure your network from unauthorized access. Mark the checkbox to set the AP it to be an open network. Tap Save to save any changes made.

Wi-Fi AP Roaming

Mark the Enable checkbox. Set the RSSI signal strength value below which the device will periodically scan for a better access point. Set a value between -50 to -90. Tap Save to save any changes made.

Restrict Login

Mark the checkbox to restrict the web interface of the device with a username and password. Enter a username and password. Tap Save to save any changes made.

Cloud

Enable to connect Shelly Device to its cloud. This allows you to control it remotely, and receive notifications and updates about your devices. Tap the toggle to enable this function.

To disable the cloud connection, click the toggle button again. A confirmation prompt will appear. Tap Confirm if you're certain you want to disable the cloud connection for this device.

Application Settings

Device Card Customization

You can customize both big and small parameter slots on your device’s card. After customization, changes apply everywhere that you see the device in the app. Tap Customize device card.

  • Choose to customize the Big Parameter Slot or Small Parameter Slot.

    • Big Parameter Slot:

      • Choose the slot as one of the following: None / Parameter.

      • If you choose the slot content as Parameter, select the parameter type from the dropdown menu.

      • View the preview below.

    • Small Parameter Slot:

      • View the list of Selected Parameters and Additonal Parameters.

      • Tao the add + button to add the Available Parameters. If you wish to remove a parameter, tap the subtract - button.

      • Tap the move button, and drag and drop the parameter to the desired position under Selected Parameters.

      • View the preview below.

  • Tap Save to save any changes made.

Exclude From Activity Log

Tap the toggle to exclude this Shelly Device from the global activity log.

Device Notifications

Click the toggle button next to each of the following notification types to enable them:

  • Enable offline email notifications.

  • Enable offline push notifications.

Share

Input an email and share control of the Device with another Shelly Smart Control user. The other user will only have access to the Main Controls, Notifications, Charts, and Application Settings tabs, and the Device Information on the Settings tab. The other user cannot see the other device tabs. View which email accounts this Shelly Device has been shared with, and click the delete button to the right of the email account you would like to delete. If a device has been shared with your account, view which account shared the device with you, and click the Remove from my account button if you wish to delete it from your account.

Settings

Eco Mode

Tap the toggle button to enable/disable Eco mode. Device will consume less energy and run at a lower temperature. Device will reboot if you enable/disable this function.

Button Type

Select from the following to set the button type:

  • Toggle switch: Toggle mode with a single switch. Switch acts as a flip switch with one state for "ON" and one state for "OFF".

  • Momentary: Set this Light to be a “Momentary” switch. Push-for “ON” or Push-for “OFF”.

  • Reverse inputs: If you enable this option, the buttons On/Off position will be inverted.

Tap Save to save any changes made.

Long Push

Set the minimum and maximum time to register a long push in milliseconds (ms). Set a minimum value between 100 ms and 3000 ms, and a maximum value between 200 ms and 6000 ms. Tap Save to save any changes made.

Multi Push

Set the maximum time between pushes in milliseconds (must be between 100 and 1000). Tap Save to save any changes made.

LED Status Disable

Click the toggle button to disable Wi-Fi status LED.

Firmware Version

Shows your current firmware version. Tap Check for update to check if a firmware updated is available. If a newer firmware version is available, you can update your Shelly device by tapping the Update button.

Geo Location And Time Zone

Set your time zone and geo-location in one of three ways:

  • Select it manually by choosing your Time zone from the dropdown menu.

  • Select your location from the map by tapping Select from map.

  • Enable automatic detection by tapping Auto detect location. You may also set automatic detection by marking the checkbox at the top of this section.

Tap Save to save any changes made.

Channel Name

Change the current channel name. Tap the toggle to sync channel name. Keep the channel name in sync with the name given in the application if “Sync name” is enabled. The sync is only from the application to the device and not vice-verse. Tap Save to save any changes made.

Device Name

Change the current device name. This will reflect on the Shelly Device name in the settings. Tap Save to save any changes made.

Factory Reset

Tap the toggle to enable factory reset from input. By enabling this setting, you can reset the Shelly Device from the device input.

Tap the toggle to enable factory reset by power cycle. By enabling this setting, you can reset the Shelly Device by 5 quick successive power cycles.

Tap the toggle to enable factory reset of the Shelly Device from the device input. Reset your Shelly Device to its factory settings by tapping the Factory reset button. This will disconnect the Shelly Device from your Wi-Fi network, and all associated users, including you, will be removed from this Device. All previously set data will be deleted.

Device Reboot

Tap Reboot to reboot your Shelly Device.

Device Information

Here you can view the Shelly Device ID, Device IP, and Device Type, and other device information. Tap the clipboard icon to copy the desired information. Tap Delete to delete this Shelly Device from your account.

JavaScript errors detected

Please note, these errors can depend on your browser setup.

If this problem persists, please contact our support.