Shelly Pro EM Device Smart Control

Main Controls

Observe the Shelly Device total power in Watts (W), apparent power in Volt-amps (VA), current in Amps (A), voltage in Volts (V), and power factor (PF). Below these measurements, observe a consumption chart, in Watt-hours (Wh), of the Shelly Device in the last 24 hours.

The power button ⏻ is at the bottom of this page. Click the power button ⏻ to turn your device On/Off. Your device is on when there is a blue ring around the power button ⏻, and is off when the ring is gray.

Consumption

Observe a chart with the Shelly Device consumption displayed in Watt-hours (Wh). Above the consumption chart, you can select the time interval and the date from which you want data to be shown. Click on the expand icon in the top right corner of the Consumption rectangular box if you wish to view the chart in full screen. Click the Export CSV button to download this data as a CSV file.

Voltage

Observe a chart with the Shelly Device maximum and minimum voltage displayed in Volts (V). Above the voltage chart, you can select the time interval and the date from which you want data to be shown. Below the voltage chart are a variety of Shelly Device measurements. Observe the average voltage in Volts (V), and the maximum and minimum voltage in Volts (V). Click on the expand icon in the top right corner of the Voltage rectangular box if you wish to view the chart in full screen. Click the Export CSV button to download this data as a CSV file.

Activity log

Observe the recorded history of the Shelly Device events. See the date, time and type of action executed such as the Device being switched On/Off.

Actions

Use events to trigger http endpoints. You can add up to 20 web hooks. Set up the following settings, and navigate between pages by clicking the NEXT or BACK buttons. Create a web hook:

• Set Action Name: Type in action name.

• Active Time: May leave as the 24-hour default option or choose an active start and end time. Click the up/down buttons, or type in a number, to set a time in hours and minutes.

• Condition: Select from a variety of conditions for the action.

  • When: Select Switch on / Switch off / Voltage change / Current change / Active power change from the dropdown menu.

  • Condition: Depending on your “When” selection, the condition setting will be different. When selected from “When” section:

    • Voltage change: Select Any / less than / greater than from the dropdown menu. If less than / greater than is selected, input a phase voltage in Volts.

    • Current change: Select Any / less than / greater than from the dropdown menu. If less than / greater than is selected, input a phase current in Amps.

    • Active power change: Select Any / less than / greater than from the dropdown menu. If less than / greater than is selected, input a phase active power in Watts.

• Actions: Add up to 5 actions.

  • Actions: Input URL to send the Shelly Device a command. Click the Add Action button to add another URL. You may add up to 5 URLs per action, which will be executed one after the other.

  • Local Actions: Set the local action as Control Output / Toggle Output from the dropdown menu. If Control Output is set as the local action, set the action as On / Off. Click the checkbox to flip value after the set number of seconds.

• Click the SAVE button to save the action or to save any changes made.

This function requires a working connection to the Internet. Once the action has been created, it will appear as a rectangular box on the main I/O actions page for the Shelly Device. You can enable/disable an action by clicking the toggle button to the left of the schedule box. You can edit the action by clicking on the edit pencil icon on the right, and delete the action by clicking the trash icon on the right.

Scripts

Use the Scripts functionality to create or import scripts.

• Library: Click the Library button to view existing scripts. Click on the desired script and click the Insert code button to add the script to your Shelly Device.

• Create new script: Click the Create new script button. A new page will appear where you can name, create, edit and save your script. Click the play button to run your script. Click the x button to exit the script. Click the trash icon to delete your script.

If there are any available, click the toggle button of the script you wish to enable. And click the play button to execute the script.

Networks

Wi-Fi

Register Shelly Device to connect to up to 2 different Wi-Fi networks. Either input or select the Wi-Fi network. Can select an open network, and also set a static IP address. Enable Wi-Fi 1, or Wi-Fi 2, or both at the same time. If both Wi-Fi 1 and Wi-Fi 2 are enabled, and Shelly Device disconnects from one of the networks, it will connect to the other.

Access Point

Enable to configure Shelly Device to create a Wi-Fi AP and you can connect to its network. Can also set it to be an open network.

Range Extender

Click the checkbox to enable range extender. Click the APPLY button to save any changes made.

Ethernet

Enable to connect Shelly Device to an ethernet cable network. Can also set a static IP address.

Outbound websocket

See outbound websocket status as Connected or Disconnected. Click the checkbox to enable SSL connectivity. Please note changing these settings requires a device reboot. Click the SAVE button to save any changes made.

RPC over UDP

Input the destination address and port. Afterwards, input the listening port. Click the Save button to save any changes made.

Cloud

Enable to connect Shelly Device to its cloud. This allows you to control it remotely, and receive notifications and updates about your devices.

Bluetooth

Enable to allow Bluetooth communication. Enable to allow Bluetooth gateway. Click the APPLY button to save any changes made.

MQTT

Enable to configure Shelly Device to execute actions via MQTT.

Application Settings

Appliance Type

Select the appliance type to which the Shelly Device is connected to. Choose one of the following from the dropdown menu: Lighting / Entertainment / Heating/cooling / Refrigeration / Laundry & cleaning / Cooking / Pool and Garden / Electric vehicle / Ventilation / Grid source / Solar source / Water heater / Roller / Other. Click the Save button to save any changes made.

Consumption Calculation

Enable/disable exclusion of device from total room/account consumption. Click the APPLY button to save any changes made.

Pin Lock

Enable/disable and set a channel pin lock.

Sync Name

Keep the device name in sync with the name given in the app.

Exclude From Activity Log

Click the checkbox to disable event log reports for this device.

Share

Input an email and share control of the Device with another Shelly Cloud user. The other user will only have access to the Device's power button (on/off), and be able to see the Device Information. The other user cannot see the other device settings.

Settings

Eco Mode

Click the checkbox to enable/disable Eco mode. Device will consume less energy and run at a lower temperature. Device will reboot if you disable/enable this function.

Device Name

Set a name for your device.

Phase selector

Set the phase by choosing from Phase A / Phase B / All.

Phase Calibration

Select the phase from which to calibrate Phase A and B of your Shelly Device.

Blink Mode Selector

Select the Blink Mode Selector as active energy or apparent energy.

Action On Power On

• On: Configure Shelly device to Turn ON, when it has power.

• Off: Configure Shelly device to Turn OFF, when it has power.

• Restore last: Configure Shelly device to Restore the last mode it was in, when it has power.

Erase data

Click the Delete button to erase all data saved on this Shelly Device.

Firmware Version

Shows your current firmware version. If a newer version is available, you can update your Shelly device by clicking the Update button.

Geo Location And Time Zone

Set your time zone and geo-location in one of three ways:

• Select it manually by choosing your Time zone from the dropdown menu.

• Select your location from the map by clicking Select from map button.

• Enable automatic detection by clicking the Auto detect location button.

Device Reboot

Reboot your Shelly Device.

Factory Reset

Reset your Shelly Device to its factory settings by clicking the Factory reset button. This will disconnect the Shelly Device from your Wi-Fi network, and all associated users, including you, will be removed from this Device. All previously set data will be deleted.

Device Information

Here you can view the Shelly Device ID, IP and other device settings.