Shelly Plus Plug UK web interface guide
To connect to your Shelly Plus Plug UK, connect your device to the Wi-Fi network with a name(SSID) like shellypluspluguk - 84CCA87D7CDC. Use the universal IP address for all Shelly devices - 192.168.33.1 to access your device's Web Interface, where you can set a Wi-fi network for the Shelly Plus Plug UK to connect to. Once done, through the app on your mobile device or through home.shelly.cloud, you can go into the Settings and search for Device information. There you will find the Device IP and be taken to the Web Interface of Shelly Plus Plug UK.
General - Home page
In the web interface, you will see five icons at the top of the screen, including one for AP, Wi-Fi, Bluetooth, Cloud and MQTT connection. Here is what the different status colors mean:
Gray: AP mode is disabled.
Blue: AP mode is enabled.
Gray: Wi-Fi connection is disabled.
White: Wi-Fi connection is enabled, but not established.
Blue: Device is connected to Wi-Fi.
Gray: Connection is disabled.
Blue: Connection is enabled.
Gray: Connection to Shelly Cloud is disabled.
White: Connection to Shelly Cloud is enabled, but not established.
Blue: Device is connected to Shelly Cloud.
Gray: MQTT is disabled.
Blue: MQTT is enabled.
You will see the toggle button, which can turn your device on or off. It’s labeled as output, but you can change its name in the settings.
Underneath, there are two sections - Last triggered by and Over Protections. In the first, you’ll see the action to be triggered on device power on, and in the second, you’ll see the current over protections and their values. By clicking one of them you can easily change them straight from this menu, or from the designated settings, explained below with the rest of the settings.
Settings - output settings
Change the displayed output name in the home page through this setting.
LED indication mode
Select between Power consumption, Switch state or Completely off. You can customize the on and off light colors, as well as the general brightness of the light.
Enable night mode and set its start and end times. During this period, your light will shine at the custom brightness you set with the slider underneath the start and end times. You can also enable action by checking the box next to Enable action, which you can then configure and once your device goes into night mode, it will complete that action. Click Save settings to save your changes.
Select either attached or detached switch.
Action on power on
Set an action for your device to complete on power on. You can turn off this setting or choose Restore last to restore the last action your device completed. Additionally, you can choose Match Input, which operates your device, according to the state of the switch or button, connected to it.
Set the value for:
Configure the actions for your device - create new actions, edit existing actions or delete actions. When creating actions for your device you will need to specify the condition on which the action occurs. You can also set a duration for your actions, as well as a URL to be hit when the condition for the action is met.
Create a weekly schedule for the day(s) and time(s) you want the corresponding device to turn On/Off automatically. You may add up to 20 weekly schedules with 5 URLs each. To add a new schedule, first enable weekly schedules by ticking the box next to Enable schedule timer. After that, click Add and then:
Select the day(s) of the week.
Choose time interval: time, sunrise, or sunset.
Set the time for the specified day(s):
Time: Click up/down button, or type in a number, to set a time in hours and minutes.
Sunset/Sunrise: The Shelly device may turn on/off automatically at sunrise/sunset, or at a specified time before or after sunrise/sunset. Click up/down button, or type in a number, to set a time in hours and minutes.
This function requires a working connection to the Internet, so the device can synchronize the time. In this setting you can also view, delete and edit your existing schedules.
Allows you to manage the power supply automatically. You may use:
Auto on: After turning off, the relay output will be automatically turned on after a predefined period of time (in seconds).
Auto off: After turning on, the relay output will be automatically turned off after a predefined period of time (in seconds).
Access Point - Configure the device's AP, including switching it on or off, and setting a password. The access point of the device is an open network by default. The SSID is unique and cannot be changed.
WiFi - Register the Shelly device to connect to up to 2 different Wi-Fi networks.
Either input or select the Wi-Fi network. Can select an open network, and also set a static IP address.
Enable Wi-Fi 1, or Wi-Fi 2, or both at the same time. If both Wi-Fi 1 and Wi-Fi 2 are enabled, and the Shelly device disconnects from one of the networks, it will connect to the other.
Bluetooth - Disable/enable Bluetooth by toggling the switch. The device's default Bluetooth setting is enabled.
Cloud -Connecting your Shelly to its cloud allows you to control it remotely, receive notifications and updates about your devices. The default for this setting is for the cloud to be enabled. If you disable the device cloud support, you will lose connection to your device from outside its local network!
MQTT - Configure the Shelly device to execute actions via MQTT. By default, MQTT is disabled, but you can enable it by toggling the switch. Changing these settings will cause the device to reboot. There are some other settings, such as RPC status notifications over MQTT (which enables you to communicate with your device through RPC notifications) and Generic status update over MQTT (to get an overall status update), which you can enable/disable by toggling the switches on their right. You can also enable SSL and type in your server, username and password, but be aware that enabling SSL will hurt the battery life and most likely shorten it by half.
Outbound Websocket - Specifies whether the HTTP channel creates an I/O exception when an inbound connection is closed while still in use by the servlet. By default, this setting is disabled. To enable it, click the toggle switch next to Enable. Enter your service address in the text box and from the drop-down menu under SSL Connectivity choose *, ca.pem or user_ca.pem.
Range extender - This setting extends the working range of your device, configuring it to work at a longer distance. To enable the extender, click the toggle switch and click Apply.
Device info - See your device’s ID, the Wi-Fi it’s connected to and the Wi-Fi RSSI.
Location and timezone - Your timezone and location will be autodetected, but you can manually change them from this setting by choosing a timezone from the drop-down menu and typing in your latitude and longitude. There is also a button Auto detect location, which will make the device automatically detect the location once again if it failed the previous time.
Authentication - If you enable authentication, you will be asked to type in a password, which you will then use to access the Web UI of the device. Once enabled, to disable it, click the toggle and enter your authentication pass once prompted.
Firmware - In this setting, you can see your device's ID, Firmware version and build ID, as well as the Web build ID. You can also see the available new versions, check for updates and easily update your device. There is also an option to upload your own firmware, however flashing devices with custom firmware irreversibly voids the device warranty.
User certificate - Upload custom SSL certificate by dragging and dropping the file or by browsing your files, which you can do by clicking the designated button.
Eco mode - Reduce energy consumption on the device by lowering CPU frequency and modem activity while in Eco Mode. To enable this setting click the toggle switch next to Enable eco mode and then click the Apply button to save the changes.
Debug - This setting includes Mqtt, Websocket and Udp debug. To enable any of these, click the toggle switch next to the specific setting. For Udp debug you will also be asked to type in a udp address.
From this setting you can download the debug logs. Enabling the debug log without a reason isn’t recommended, since your device will be slowed down and this setting will cause aging of the flash memory. If you do decide to enable it, you can also download the previous and current logs. Be aware that leaving this page will reset the logger and logged data.