Shelly Plus 0-10V Dimmer Device Smart Control

Main Controls

Below the Main Controls heading, observe brightness as a percentage. Adjust brightness with the Shelly Device by tapping and dragging the vertical slider up and down to your desired percentage, with the percentage value shown just below the slider.

The power button ⏻ is at the bottom of this tab. Tap the power button ⏻ to turn your device On/Off. Your device is on when there is a blue ring around the power button ⏻, and is off when the ring is gray.

Notifications

If you have Shelly Device notifications, they will appear on this tab. View the number of notifications for this Shelly Device. Tap the X button in the top right corner of the notification box if you wish to delete the notification.

Activity log

Observe the recorded history of the Shelly Device events. See the date, time and type of action executed such as the Device being switched On/Off.

Timer

In this tab, you can set a timer to manage the device on/off state.

1. Choose from the following options:

• Auto on: Enter the number of seconds that should pass for the device to be switched on after it has been turned off. Mark the empty checkbox to enable the timer.

• Auto off: Enter the number of seconds that should pass for the device to be switched off after it has been turned on. Mark the empty checkbox to enable the timer.

2. Tap Save to confirm the setting.

Schedule

Tap Add schedule to create a schedule. Create a weekly schedule for the day(s) and time(s) you want the corresponding device to turn On/Off automatically, or to change to a specified brightness. You may add up to 20 weekly schedules. This function requires a working connection to the Internet.

• Mode Selection: Select the mode as Simple or Advanced for selecting days of the week.

  • Simple: Choose Simple mode to select day(s) of the week.

  • Advanced: Switch to Advanced mode for more complex schedules.

• Choose Weekday: Select the day(s) of the week.

  • Simple: Select the day(s) of the week.

  • Advanced:

    • Specific days: Tap the toggle to select specific days of the month. When inactive, this function applies to all days of the month. Set the active days of the month by tapping on the desired date(s). You may also select dates using the following buttons:

      • Select even

      • Select odd

      • Enter the dates "From" and "To" that you want to set as active dates, then tap Select to choose these dates.

      • Tap Clear to clear selected dates.

    • Specific months: Tap the toggle to select specific months. When inactive, this function applies to all months. Select the active months using the following buttons:

      • Select even

      • Select odd

      • Enter the dates "From" and "To" that you want to set as active dates, then tap Select to choose these dates.

      • Tap Clear to clear selected dates.

  • Tap Next.

• Choose time interval: Select the mode as Simple or Advanced.

  • Simple: Choose Simple mode to select a specific time or intervals based on Sunrise/Sunset. Choose from Time, Sunrise / Sunset, and set the time for the previously selected day(s):

    • Time: Tap the up/down button, or enter a number, to set a time in hours and minutes.

    • Sunset / Sunrise: The Shelly device may turn on/off automatically at sunrise/sunset, or at a specified time Before/After Sunrise/Sunset. Select the time in hours and minutes from the dropdown menus.

  • Advanced: Choose Advanced mode for more complex schedules. Observe the selected times at which the schedule will be executed at the bottom of this page. Tap the toggle of the following to set them up: Hours / Minutes / Seconds. Set up each of these time units by tapping on the desired time in hours/minutes/seconds, or by tapping on the following buttons:

    • Select even

    • Select odd

    • Enter the number "From" and "To" that you want to set as the active time, then tap Select to choose these times.

    • Tap Clear to clear selected time.

• Add local action: You can add up to 5 actions per schedule. Tap + Add local action to add an action. Set the local action as Control Light / Toggle Light.

  • Control Light: Follow these steps if you select Control Light.

    • Mark the checkbox to enable Light State. Set the light state as On / Off. Mark the checkbox to flip the value after the set number of seconds.

    • Mark the checkbox to set the Brightness Property, and tap and drag the slider to adjust the brightness.

    • Mark the checkbox to set the transition duration property. Enter a value in seconds between 0.5 and 10800 seconds.

  • Tap Save to save the schedule action. Once saved, tap on the action to edit it, or tap the trash icon to the right of it to delete the action.

• Tap Save to save the schedule.

Once the schedule has been created, it will appear as a rectangular box on the main Schedule page for the Shelly Device. On this box, you can see the schedule details such as the days of the week, action and time. You can enable/disable a schedule by tapping the toggle button on the left of the schedule box. You can edit the schedule by tapping on the edit pencil icon on the right, and delete the schedule by tapping the trash icon on the right.

Actions

Use events to trigger HTTP endpoints. You can add up to 20 actions. Set up the following settings, and navigate between pages by tapping the Next or Back buttons. Tap Add action to create an action:

• Choose Component: Choose the component from the dropdown menu, choose from the following: Light / Input (0) / Input (1).

• Set Action Name: Type in action name.

• Active Time: Mark the checkbox to set the active time. You may leave it as the 24-hour default option or choose an active start and end time. Tap the up/down buttons, or enter a number, to set a time in hours and minutes.

• When: Select from a variety of conditions for the button/switch depending on the previously chosen component.

  • Light on

  • Light off

  • Input on

  • Input off

• Repeat When: Input the minimum interval, in seconds, between two consecutive invocations of the webhook. Any events that trigger the webhook within the specified time interval will be automatically suppressed.

• Actions: Input URL to send the Shelly Device a command. You may add up to 5 URLs per action, which will be executed one after the other. Tap + Add URL to add another URL to execute, or tap + Add action from another device to add an action from another device. If you choose to add an action from another device, set it as a Control Output / Toggle Output local action, and set the action as On/Off. You may also add a local action.

  • Local action: Tap + Add local action to add a local action. Set the local action as Control Light / Toggle Light. Follow these steps if you select Control Light.

    • Light State: Mark the checkbox to enable Light State. Set the light state as On / Off. Mark the checkbox to flip value after the set number of seconds.

    • Brightness Property: Mark the checkbox to set the Brightness Property, and tap and drag the slider to adjust the brightness.

    • Transition Duration Property: Mark the checkbox to set the transition duration property. Enter a value in seconds between 0.5 and 10800 seconds.

  • Once you save an action, tap on the edit icon pencil to edit it, or tap the trash icon to the right of it to delete the action.

• Tap Save to save the action or to save any changes made.

This function requires a working connection to the Internet. Once the action has been created, it will appear as a rectangular box on the main Actions page for the Shelly Device. You can enable/disable an action by tapping the toggle button to the left of the action box. You can edit the action by tapping on the edit pencil icon on the right, and delete the schedule by tapping the trash icon on the right.

Night mode

Tap the toggle to enable night mode. Tap the edit icon to adjust the active night mode settings.

• Choose time interval: Choose the night mode time interval by tapping the up/down buttons, or type in a number, to set a time in hours and minutes. Tap Next.

• Select Brightness: Tap and drag the horizontal slider to set the brightness.

• Tap Save to save any changes made.

Add-on Peripherals

Tap ENABLE ADD-ON to enable the add-on functionality to this Shelly Device, which requires a restart of the Shelly Device.

Manage peripherals

Tap Add Peripheral to add an Add-on Peripheral. Please note after adding a peripheral, the Shelly Device will reboot. Select from one of the following Add-on Peripherals:

• Temperature and Humidity

• Temperature sensor

• Digital Input

• Analog Input

• Voltmeter

Tap the settings icon if you wish to edit your peripheral. Tap the trash icon of the add-on peripheral you wish to delete it.

Actions

Tap Add action to add an action for an add-on peripheral. Choose the peripheral, set the action name, active time, set up the conditions to trigger the action, and the actions to

• Choose Peripheral: Choose a peripheral from the dropdown menu.

• Set Action Name: Set the action name.

• Active Time: Mark the checkbox to set an active time. You may leave it as the 24-hour default option or choose an active start and end time. Tap the up/down buttons, or enter a number, to set a time in hours and minutes. Set the time as AM or PM.

• When:

  • Select from a variety of conditions for the button/switch. The possible conditions will vary for each peripheral.

  • Repeat When: Enter the minimum interval, in seconds, between two consecutive invocations of the webhook. Any events that trigger the webhook within the specified time interval will be automatically supressed.

• Actions: Input URL to send the Shelly Device a command. You may add up to 5 URLs per action, which will be executed one after the other. Tap + Add URL to add another URL to execute, or tap + Add action from another device to add an action from another device. If you choose to add an action from another device, set it as a Control Output / Toggle Output local action, and set the action as On/Off. You may also add a local action.

  • Local Actions: Tap + Add local action to create a local action. Select Control Output / Toggle Output from the dropdown menu to set the type of local action. If Control Output is selected, set the action as On / Off. Mark the checkbox to flip value after the set number of seconds, and enter the number of seconds. Tap Save to save the action. Once the action has been created, tap the trash icon to the right of it if you wish to delete it.

• Tap Save to save the action or to save any changes made.

Scripts

Use the Scripts functionality to create or import scripts.

• Library: Tap Open Library to view existing scripts. Tap on the desired script and tap Insert code to add the script to your Shelly Device.

• Create new script: Tap Create new script. A new page will appear where you can name, create, edit, and save your script. Tap the play button to run your script. Tap x to exit the script. Tap the trash icon to delete your script.

For an existing script, tap the toggle of the script you wish to enable. Tap the play button of the script you wish to execute. Tap the edit pencil icon to update the script, and the trash icon to delete it.

Networks

Wi-Fi

Register Shelly Device to connect to up to 2 different Wi-Fi networks. Either input or select the Wi-Fi network. Can select an open network, and also set a static IP address. Enable Wi-Fi 1, or Wi-Fi 2, or both at the same time. If both Wi-Fi 1 and Wi-Fi 2 are enabled, and Shelly Device disconnects from one of the networks, it will connect to the other. Tap Save to save any changes made.

Access Point

Mark the checkbox to enable this function. Enable to configure Shelly Device to create a Wi-Fi Access Point (AP), to which you can connect. Observe the SSID. Set a password to protect your device’s access point to secure your network from unauthorized access. Mark the checkbox to set the AP to be an open network. Tap Save to save any changes made.

Range extender

Tap the toggle to enable the range extender.

Outbound websocket

Mark the checkbox to enable SSL connectivity. See outbound websocket status as Connected or Disconnected. Select the type of SSL connectivity from the dropdown menu, and input the server address. Please note changing these settings requires a device reboot. Tap Save to save any changes made.

RPC over UDP

Enter the destination address and port. Afterwards, enter the listening port. Tap Save to save any changes made.

Cloud

Enable to connect Shelly Device to its cloud. This allows you to control it remotely, and receive notifications and updates about your devices. Tap the toggle to enable this function.

To disable the cloud connection, tap the toggle again. A confirmation prompt will appear. Tap Confirm if you're certain you want to disable the cloud connection for this device.

Bluetooth

Mark the checkbox to enable Bluetooth. Tap the toggle to enable RPC and/or Bluetooth gateway.

MQTT

• Mark the checkbox to enable MQTT. Configure the Shelly Device to execute actions via MQTT. Please note changing the MQTT settings requires a device reboot.

• Choose the connection type, choose from the following options:

  • RPC status notifications over MQTT

  • Generic status update over MQTT

  • SSL connectivity

• Enter the MQTT prefix, the desired server, and client ID.

• Enter the username and password.

• Tap Save to save any changes made.

Application Settings

Offline Notifications

Tap the toggle next to each of the following notification types to enable them:

• Enable offline email notifications.

• Enable offline push notifications.

Device Card Customization

You can customize both big and small parameter slots on your device’s card. After customization, changes apply everywhere that you see the device in the app. Tap Customize device card to customize the device card.

• Choose to customize the Big Parameter Slot or Small Parameter Slot.

  • Big Parameter Slot:

    • Choose the slot as one of the following: None / Action / Parameter.

    • If you choose the slot content as Parameter, select the parameter type from the dropdown menu.

    • View the preview below.

  • Small Parameter Slot:

    • View the list of Selected Parameters and Additonal Parameters.

    • Tap the add + button to add the Available Parameters. If you wish to remove a parameter, tap the subtract - button.

    • Tap the move button, and drag and drop the parameter to the desired position under Selected Parameters.

    • View the preview below.

• Tap Save to save any changes made.

Energy Calculation

Tap the toggle to enable/disable exclusion of device from total room/account energy.

Pin Lock

Tap the toggle to enable and set a channel pin lock.

Input State Display

Tap the toggle to add an input state identifier to the power button. Turn on indicator for the current status of the physical switch connected to Shelly Device. When enabled, a small line appears on the power button, below the power symbol ⏻. A red line indicates the physical switch is off, while a blue line indicates the physical switch is on.

Exclude From Activity Log

Tap the toggle to exclude this Shelly Device from the global activity log.

Forgotten Lights Reminder

You can enable the device “Forgotten Lights Reminder” if your device is designated as a “light” in the “Appliance type” setting. Tap the first toggle to enable forgotten lights tracking. Tap the next toggles to enable forgotten lights email and push notifications.

Share

Input an email and share control of the Device with another Shelly Smart Control user. The other user will only have access to the Main Controls, Notifications, Charts, and Application Settings tabs, and the Device Information on the Settings tab. The other user cannot see the other device tabs. View which email accounts this Shelly Device has been shared with, and click the delete button to the right of the email account you would like to delete. If a device has been shared with your account, view which account shared the device with you, and tap Remove from my account if you wish to delete it from your account.

Settings

Input/Output Settings

These settings define the way the attached switch or button controls the output state. Set the input mode by selecting Button/Switch. You can set the relay type, and relay power condition when the Shelly device has power depending on the preferred usage of the device.

Set relay type:

• Set Shelly device to be "Toggle" switch. Act as a flip switch with one state for "ON" and one state for "OFF". (Switch only)

• Set Shelly device to be "Edge" switch. Changes state on every hit. (Switch only)

• Set Shelly device to be in "Detached" switch mode - switch is separated from the relays. (Button and Switch)

• Activation Switch - Used with motion sensor. Any input turns ON and resets Auto Off timer. (Switch only)

• One button dimming control - Push to toggle, hold to dim up/down (changes direction on each hold). (Button only)

• Dual Button dim mode - 2 inputs configuration (buttons) for up/down. (Button only)

Action on power on:

• On: (Button and Switch) - Configure Shelly device to Turn ON, when it has power.

• Off: (Button and Switch) - Configure Shelly device to Turn OFF, when it has power.

• Restore last: (Button and Switch) - Configure Shelly device to Restore the last mode it was in, when it has power.

Tap Save to save any changes made.

Input Type

Set type for device input 0:

• Button

• Switch

Set type for device input 1:

• Button

• Switch

Tap Save to save any changes made.

Enable Input

Tap the toggle to enable an input.

Invert Input

Tap the toggle to invert device input 0/1.

Input Name

Set name for device input 0 and 1. Tap Save to save any changes made.

Button Fade Rate

The button fade rate controls how quickly the output brightness changes while the button is held down for dimming. Select a rate between 1x and 5x from the dropdown menu. Tap Save to save any changes made.

Min Brightness on Toggle

Brightness level (as a percentage) applied when there is a toggle and current brightness is lower than ‘Min brightness on toggle’. Enter a value between 0 and 100. Tap Save to save any changes made.

Min/Max Brightness

Enter a value between 0 and 100 to set the minimum/maximum brightness. This function remaps output 0%-100% range range to the specified values here. Please note that changing these settings requires a device reboot.

Transition Duration

Enter a value between 0 and 5 seconds for the transition time. Tap Save to save any changes made.

Device Name

Change the current device name. Tap the toggle to sync device name. Keep the device name in sync with the name given in the application if “Sync name” is enabled. The sync is only from the application to the device and not vice-versa. Tap Save to save any changes made.

Firmware Version

Shows your current firmware version. Tap Check for update button to see if a new firmware version is available. If a newer firmware version is available, you can update your Shelly device by tapping the Update button.

Update Automatically

Tap the toggle to Enable auto update. Add a schedule to automatically check and update the Shelly device to the latest stable firmware version. Tap Edit schedule, which will direct you to the Schedule page for this Shelly Device. Tap the edit pencil icon and follow these steps to edit the settings of the schedule:

• Choose Weekday: Select the mode as Simple or Advanced for selecting days of the week.

  • Simple: Choose Simple mode to select day(s) of the week.

  • Advanced: Switch to Advanced mode for more complex schedules.

    • Specific days: Tap the toggle to select specific days of the month. When inactive, this function applies to all days of the month. Set the active days of the month by tapping the desired date(s). You may also select dates using the following buttons:

      • Select even

      • Select odd

      • Enter the dates "From" and "To" that you want to set as active dates, then tap Select to choose these dates.

      • Tap Clear to clear selected dates.

    • Specific months: Tap the toggle to select specific months. When inactive, this function applies to all months. Select the active months using the following buttons:

      • Select even

      • Select odd

      • Enter the dates "From" and "To" that you want to set as active dates, then tap Select to choose these dates.

      • Tap Clear to clear selected dates.

  • Tap Next.

• Choose time interval: Select the mode as Simple or Advanced.

  • Simple: Choose Simple mode to select a specific time or intervals based on Sunrise/Sunset. Choose from Time, Sunrise / Sunset, and set the time for the previously selected day(s):

    • Time: Tap the up/down button, or type in a number, to set a time in hours and minutes.

    • Sunset / Sunrise: The Shelly device may turn on/off automatically at sunrise/sunset, or at a specified time Before/After Sunrise/Sunset. Select the time in hours and minutes from the dropdown menus.

  • Advanced: Choose Advanced mode for more complex schedules. Observe the selected times at which the schedule will be executed at the bottom of this page. Tap the toggle of the following to set them up: Hours / Minutes / Seconds. Set up each of these time units by tapping on the desired time in hours/minutes/seconds, or by tapping the following buttons:

    • Select even

    • Select odd

    • Enter the number "From" and "To" that you want to set as the active time, then tap Select to choose these times.

    • Tap Clear to clear selected time.

  • Tap Next.

• Local Action: This action has already been set up to automatically check and update the Shelly device to the latest stable firmware version. Tap Next.

• View the schedule details.

• Tap Save to save any changes made.

• Tap the trash icon on the schedule if you wish to delete it.

Geo Location And Time Zone

Set your time zone and geo-location in one of three ways:

• Select it manually by choosing your Time zone from the dropdown menu.

  • Enter your location Latitude and Longitude.

• Select your location from the map by tapping Select from map.

• Enable automatic detection by tapping Auto detect location.

Tap Save to save any changes made.

Device Reboot

Tap Reboot to reboot your Shelly Device.

Factory Reset

Reset your Shelly Device to its factory settings by tapping Factory reset. This will disconnect the Shelly Device from your Wi-Fi network, and all associated users, including you, will be removed from this Device. All previously set data will be deleted.

Device Information

You can view the ID, IP and other settings of your device. Copy Device ID, Decimal ID, Device IP, and Device Type by tapping the copy icon to the right of each. Tap Delete to remove this device from your Shelly account.