Shelly Plus i3 Device Page
Status and Control
From left to right across the status and control bar, you see the Device image, name, and a power button ⏻. Click the power button ⏻ to turn your device on/off. Your device is on when there is a blue ring around the power button ⏻, and is off when the ring is gray.
If a firmware update is available, then you will observe a "Firmware Update Available" text below the status and control bar. Click the UPDATE button to update your Shelly Device firmware.
Settings
I/O Actions
Use events to trigger http endpoints. For each possible condition, click the Enable checkbox to enable the condition. Input up to 5 URLs per condition. The possible conditions are:
Button off
Button short push
Button long push
Button double short push
Button triple short push
Button short and long push
Button long and short push
Internet
Wi-Fi
Register the Shelly device to connect to up to 2 different Wi-Fi networks. Either input or select the Wi-Fi network. Can select an open network, and also set a static IP address. Enable Wi-Fi 1, or Wi-Fi 2, or both at the same time. If both Wi-Fi 1 and Wi-Fi 2 are enabled, and the Shelly device disconnects from one of the networks, it will connect to the other.
Access Point
Enable to configure the Shelly device to create a Wi-Fi AP and you can connect to its network. Can also set it to be an open network.
Wi-Fi AP Roaming
Click the Enable checkbox. Set the RSSI signal strength value below which the device will periodically scan for a better access point. Set a value between -50 to -90. Click the APPLY button to apply any changes made.
Restrict Login
Restrict the web interface of the device with a Username and Password.
Cloud
Enable to connect Shelly Device to its cloud. This allows you to control it remotely, and receive notifications and updates about your devices.
Application Settings
Exclude From Event Log
Do not show event log reports for this device in the app.
Sync Name
Keep the device name in sync with the name given in the app.
Share
Input an email and share control of the Device with another Shelly Cloud user. The other user will only have access to the Device's power button (on/off), and be able to see the Device Information. The other user cannot see the other device settings.
Settings
Eco Mode
Device will consume less energy and run at a lower temperature. Device will reboot if you disable/enable this function.
Button Type
Select from the following to set button type:
Momentary - Set Shelly device to be a “Momentary” switch. Push-for “ON” or Push-for “OFF”.
Toggle switch - Set this Inputs reader to be a “Toggle” switch. Switch acts as a flip switch with one state for "ON" and one state for "OFF".
Edge switch - edge on/off mode with single switch. Changes state on every hit.
Reverse inputs - If you enable this option, the buttons On/Off position will be inverted.
Long Push
Set the minimum and maximum time to register a long push in milliseconds (ms). For the minimum value set a value between 100 to 300 ms. For the maximum value set a value between 200 to 6000 ms.
Multi Push
Set the max time between pushes of the button between 100 and 1000 milliseconds. Click the SAVE button to save any changes made.
LED Status Disable
Click the check box to disabled Wi-Fi status LED.
Firmware Update
Shows your current firmware version. If a newer version is available, you can update your Shelly device by clicking the UPDATE button.
Geo Location And Time Zone
Set your time zone and geo-location manually, or enable/disable automatic detection.
Device Name
Change the current device name. This will reflect on the device name in the application if the “Sync name” application setting is enabled. Click the SAVE button to save any changes made.
Factory Reset
Remove Shelly Device from your account and return it to its factory settings. This will delete all set data.
Device Reboot
Reboot your Shelly Device.
Device Info
Here you can view the ID, IP and other settings of your device.
Upon clicking Edit device, you can change the room, name or image of the device.