Shelly H&T Device Page
Status and control
From left to right across the status and control bar, you see the Device image, name, and current room temperature. Directly below the status and control bar is the current room humidity and Device battery as percentages.
The status and control bar remains at the top of the Device page, when you click on either the Status and control or Settings tab.
Temperature
Observe a chart with the Shelly H&T recorded temperature given in ºC/ºF (change this under Device Settings). Above the temperature chart, you can select the time interval and the date from which you want data to be shown. The temperature chart shows the maximum and minimum temperature of the room throughout the chosen time interval. Below the temperature chart you have the option to download the temperature data by clicking the DOWNLOAD button. This downloads a table of your Shelly H&T temperature data.
Humidity
Observe a chart with the Shelly H&T recorded humidity given as a percentage. Above the humidity chart, you can select the time interval and the date from which you want data to be shown. Below the humidity chart you have the option to download the humidity data by clicking the DOWNLOAD button. This downloads a table of your Shelly H&T humidity data.
If a firmware update is available, then you will observe a "Firmware Update Available" text below the humidity chart. Click the UPDATE button to update your Shelly Device firmware.
Settings
Sensor Settings
External Power
Enable if an external power supply is connected to the Shelly H&T.
Temperature Units
Select ºC/ºF to be the units shown the temperature on the display.
Temperature Threshold
Input a value in Celsius (ºC) for the threshold temperature change which will cause the Device to wake up and trigger a sensor data report. (Min: 0.5 ºC - Max: 5 ºC)
Humidity Threshold
Input a value for the threshold relative humidity change which will cause the Device to wake up and trigger a sensor data report. (Min: 1 % - Max: 20 %)
Humidity Offset
Set the humidity offset. The value must be between -50 and 50.
I/O Actions
Use events to trigger http endpoints. Enable Sensor reports (URLs) to hit URLs when the the device wakes up. Input URLs to send the Shelly device a command. You may add up to 5 URLs per web hook, which will be executed one after the other.
Sensor Actions
When Shelly H&T wakes up, the following actions will be executed.
For each possible condition, check the checkbox to enable the condition. Input up to 5 URLs in order to trigger http endpoints. Set a start and end time for these actions. Possible conditions are:
Temperature over
Temperature under
Humidity over
Humidity under
Internet
Wi-Fi
Register the Shelly device to connect to up to 2 different Wi-Fi networks. Either input or select the Wi-Fi network. Can select an open network, and also set a static IP address. Enable Wi-Fi 1, or Wi-Fi 2, or both at the same time. If both Wi-Fi 1 and Wi-Fi 2 are enabled, and the Shelly device disconnects from one of the networks, it will connect to the other.
Access Point
Enable to configure the Shelly device to create a Wi-Fi AP and you can connect to its network. Can also set it to be an open network.
Restrict Login
Restrict the web interface of the device with a Username and Password.
Application Settings
Exclude From Event Log
Do not show event log reports for this device in the app.
Sync Name
Keep the device name in sync with the name given in the app.
Share
Input an email and share control of the Device with another Shelly Cloud user. The other user will only have access to the Device's power button (on/off), and be able to see the Device Information. The other user cannot see the other device settings.
Settings
Firmware Update
Shows your current firmware version. If a newer version is available, you can update your Shelly device by clicking the Update button.
Geo Location And Time Zone
Set your time zone and geo-location manually, or enable/disable automatic detection.
Device Name
Set a name for your device.
Factory Reset
Remove Shelly Device from your account and return it to its factory settings. This will delete all set data.
Device Information
Here you can view the ID, IP and other settings of your device. Upon clicking Edit device, you can change the room, name or image of the device.